- LED tube as an energy-saving replacement for fluorescent tubes ,- Easy exchange of fluorescent tubes, which are operated in lamp housing using starters and a conventional AC-adapter (CLB and LLB) ,- No conversion of lights required - the supplied dummy starter must, however, be exchanged with the existing starter ,- Immediate start without flickering even at low temperatures down to -20°C ,- The brightness in the primary beam direction is almost identical to that of fluorescent tubes (except when the light is fitted with highly efficient specular louvres) ,- Long service life even when switched on frequently ,- Saves about 50% energy compared with conventional fluorescent tubes , ,Note for Consumers: ,Only for private use and not for long-term commercial use ,Only for use in individual switching (lights have their own starter for each fluorescent tube) ,Not suitable for electronic ballasts (lights without starters) , ,CLB = Conventional Loss Ballast, the most widespread system ,LLB = Low Loss Ballast ,EB = Electronic Ballast , ,Any changes to the wiring should only be carried out by qualified electricians. Incorrect installation could result in injury or damage to property. ,Before carrying out any conversion work, ensure that there is no voltage. ,Any defects due to incorrect installation are not covered by the warranty. ,In addition to the power consumption of the LED tubes, CLBs that have not been disconnected/bypassed in particular have a high and unnecessary power loss and can cause high voltage peaks. Voltage peaks reduce the service life of the tubes. The disconnection/bypass must only be carried out by a qualified electrician. ,Power loss in LLBs is considerably lower and so disconnection/bypass is not so important. , ,If a light that has been converted to LED tubes is refitted with fluorescent tubes, a fluorescent tube starter will need to be refitted. Every light that has been converted to LED tubes should feature a warning notice next to the starter. , ,The overall efficiency and light distribution is determined not only by the characteristics of the LED tubes, but also by the construction and characteristics of the lights. - Can be Dimmed: No ,- Colour Temperature: 4000 K ,- Design: T8 ø 26 mm rod-shaped ,- LED Type: SMD ,- Lamp Survival Factor at 6000h (min.): 0.9 ,- Light color / color temperature: Neutral White - 4000 K ,- Light efficiency: 100 lm/W ,- Nominal Service Life: 30000 h ,- Number of Switching Cycles until Premature Failure (min.): 30000 ,- Operating Position: 360 ° ,- Optimal Ambient Temperature: 25 °C ,- Power Consumption of an Equivalent Incandescent Lamp: 36 W ,- RA-Value: 80 ,- Socket: G 13 ,- Starting Time (max.): 0.5 s ,- Diameter: 29.5 mm ,- Dimensions Differ From Those of a Standardized Bulb: No ,- Height: 1200 mm ,- Net Weight: 227 gr ,- Energy Efficiency Class: A+ (Scale from A++ to E, Optimum Value: A++) ,- Lamp Current: 90 mA ,- Lamp Lumen Factor at End of Nominal Service Life (min.): 0.700 ,- Rated Power Consumption: 18 W ,- Rated Service Life: 30000 h ,- Colour Consistency: 6 ,- EAR Reg.No.: DE 38720470 ,- Electrical Efficiency Factor of the Bulb (min.): 0.9 ,- Lamp Lumen Maintenance Factor at 6000h: 0.8 ,- Mains Frequency: 50 Hz ,- Nominal Beam Angle: 220 ° ,- Nominal Light Output: 1800 lm ,- Nominal Power Consumption: 18 W ,- Operating Voltage: 230 V ,- Premature Failure Rate: 5 % ,- Rated Beam Angle: 220 ° ,- Rated Light Output: 1800 lm ,- Start-Up Time Until 95% of Full Light Output Has Been Reached (max.): 1 s ,- Weighted Energy Consumption: 18 kWh/1000h ,- Colour Reproduction Index RA (min.): 80 ,- Light Colour: Neutral White ,- Bulb Serves as Replacement for Standard Bulbs of This Size: Fluorescent Tube ,- Suitable for Accent Lighting: No 2 years legal warranty only